XST-235-7H1 Steam-Free Leather Seam Pressing Machine
Product Summary
XST-235-7H1 Steam-Free Leather Seam Pressing Machine A pressing machine purpose-built for leather seam opening — automatic seam opening, steam-free pressing that prevents deformation and discoloration, and operator onboarding measured in minutes. Product Overview Leather is the material that ...
Product Custom Attributes
Steam-Free leather pressing machine
,Leather seam ironing machine
,Steam-Free ironing machine with warranty
Basic Properties
Trading Properties
Product Description
A pressing machine purpose-built for leather seam opening — automatic seam opening, steam-free pressing that prevents deformation and discoloration, and operator onboarding measured in minutes.
Leather is the material that punishes a pressing station hardest. Steam carries moisture into the hide, and leather responds to moisture and heat together by deforming, shrinking and shifting colour — damage that cannot be pressed back out afterwards. The XST-235-7H1 is built around that constraint. It is an independently developed garment seam pressing machine that uses no steam at all, replacing manual pressing in the leather seam opening process with an automated, temperature-controlled operation.
Its working function is narrow and specific: opening and pressing flat the seam allowance on leather panels, so leather fabric seam opening reaches a consistent, production-grade standard. Seam opening runs automatically, and the pressing stroke is continuous rather than stop-start, at an adjustable speed up to 100 mm/s across a 5-20 mm pressing width. Because heat is applied by contact instead of carried in vapour, the hide never passes through a high-humidity stage — which is the mechanism behind the deformation and discoloration results.
Under the machine: dual servo motors rated 100 W + 100 W drive feed and pressing motion, overall power consumption is 280 W, working pressure is 0.6-0.7 MPa, and the unit runs on AC 220 V ±10%, 50/60 Hz. The manufacturer states an operator onboarding time of roughly three minutes.
Seam opening is where hand work is slowest and least repeatable. The machine is designed specifically around this step, opening the seam automatically rather than relying on operator technique.
With no steam in the process, moisture never reaches the leather. Deformation, shrinkage and colour shift are removed at the source instead of being corrected later.
Pressing temperature is controlled precisely, so one machine can serve different materials on the same line. Settings are repeatable from shift to shift and operator to operator.
The simplified interface shortens training, lowers required skill levels, and makes it practical to move operators between stations when production plans change.
Three subsystems replace the conventional steam chain:
- Intelligent temperature control — heat is delivered by contact and held at the set value, instead of being carried into the material by water vapour.
- Mechanical transport — dual servo motors carry seam opening and pressing through in one continuous pass, so feed is set by the machine rather than by hand.
- Steam elimination — the hide never enters a high-humidity condition, which is the mechanism behind the deformation and discoloration results.
| Parameter | Specification |
|---|---|
| Model | XST-235-7H1 |
| Pressing Speed | 100 mm/s (adjustable) |
| Pressing Width | 5-20 mm |
| Pressing Stroke | Continuous |
| Working Pressure | 0.6-0.7 MPa |
| Motor Power | 100 W + 100 W (dual servo motors) |
| Overall Power | 280 W |
| Power Supply | AC 220 V ±10%, 50/60 Hz |
The XST-235-7H1 is developed for the seam opening step in leather garment manufacture — leather outerwear and leather jackets among them — where the seam allowance has to be opened and pressed flat as part of building the panel.
Four points to confirm before specifying the machine:
- Pressing width: The machine covers a 5-20 mm band. Measure your actual seam allowance and edge width.
- Plant air supply: Working pressure is 0.6-0.7 MPa, so a compressed air line must be available.
- Electrical supply: Single-phase AC 220 V ±10% at 50/60 Hz.
- Material range: Confirm leather weights, finishes, and temperature settings with the supplier.
Because the stroke runs continuously, the machine suits seam opening in continuous production rather than one-off finishing work.
Moisture-driven deformation and colour change in leather cannot be reworked. Removing steam eliminates this failure mode upstream of inspection.
Overall power is 280 W with no steam generation. Compared with boiler-fed stations, the largest cost difference accumulates across a full shift.
Automatic seam opening at controlled temperature and feed rate produces the same result regardless of operator experience level.
Minutes-long onboarding lowers recruitment requirements and shortens ramp-up time for new styles and frequent changeovers.
- Purpose-built for leather seam opening: Designed specifically for opening and flattening seam allowance on leather with automatic operation.
- No steam infrastructure: Eliminates boiler, steam generation, and associated running costs from the station.
- Dual servo drive with continuous stroke: Two 100 W motors carry seam opening and pressing through in one pass at adjustable speed up to 100 mm/s.
- Industry-first development: Positioned as the first steam-free pressing machine in garment seam pressing equipment.
Being clear about where a machine stops is part of specifying it correctly:
- Pressing width is bounded: The 5-20 mm working band suits seam opening and edge work; not a wide-area pressing surface.
- Compressed air required: Supply at 0.6-0.7 MPa must be available at the station.
- Single-phase 220 V supply: Installations on other supply configurations need verification.
- Temperature is material-dependent: Settings must be matched to the specific leather or fabric in production.
- Focused function: Specifically for leather seam opening and pressing, not general-purpose garment finishing.
No. The machine is built around the absence of steam, so no boiler, steam generator or steam iron is required. It needs compressed air and electrical connection instead — removing steam is what keeps moisture out of the leather.
Working pressure is 0.6-0.7 MPa, and the machine runs on AC 220 V ±10%, 50/60 Hz. Both should be confirmed at the installation point before delivery.
The machine covers a 5-20 mm band. Start selection from your actual seam allowance and edge width rather than the machine's maximum — this determines whether the pressing foot sits correctly over your seam.
The machine is designed for leather seam opening, but its precise temperature control allows settings to be matched to different materials. Confirm specific materials and temperature settings with the supplier before purchase.
Dual servo motors rated 100 W + 100 W. Overall machine power is 280 W with no steam generation load — a key difference against conventional pressing stations.
Contact Our Experts And Get A Free Consultation!
Our mission is to offer "High Quality" & "Good Service" & "Fast Delivery" to help our clients to gain more profits.
